Crack4sure Logo
3 Months Free Update
3 Months Free Update
3 Months Free Update
When modifying a cluster's settings, what value can be changed from the Environment Settings screen in Deployment Manager?
What is the maximum number of copies supported using the MetroPoint topology for VPLEX continuous data replication?
Which Open Replicator mode is used by the RecoverPoint VMAX write splitter?
You are deploying a RecoverPoint cluster into an existing VPLEX environment. You want to validate the following conditions:
In addition, you want to verify that the VPLEX management server can reach all of the attached RecoverPoint clusters.
How can you verify all the information?
An administrator performs a Consistency Group failover to a remote cluster. What happens to the data stored in the copy journal after the copy journal becomes the production journal?
The VSI RecoverPoint Management plug-in can protect datastores accessed by the ESXi host using which protocols?
Which RecoverPoint tool will give you an overview of the system state, based on the system’s long term statistics?
For optimal performance when presenting gatekeepers for a VMAX splitter, how many FA ports should be used in each port group?
A customer is interested in implementing a RecoverPoint solution using a four-node cluster with physical RPAs. How many total IP addresses are required for the cluster?
You are concerned about the performance of the RecoverPoint replication. Some of the Consistency Groups continue to go into High Load. Initial troubleshooting points to a data compression issue.
Which command will determine if compression is set too high?
When adding a new vRPA, what is the only storage authentication method that is supported?
A customer is evaluating the deployment of RecoverPoint with their VNX array. They want to deploy the RPAs in virtual appliance form. They ask your opinion about using vRPA versus physical appliances.
What should you advise them?
When choosing a journal for a CG what would be a factor in selecting which LUNs to use?
A Consistency Group is experiencing High Load twice a day in a RecoverPoint remote replication environment.
What is a possible reason for the High Load to occur on the Consistency Group?
In a EMC RecoverPoint environment, which EMC product adds support for heterogeneous storage systems?
An administrator experiences a serious error with an RPA and calls EMC Support to resolve the issue. They are concerned that the system did not automatically notify EMC Support via the ESRS gateway. You check all settings in Unisphere Configure System Notification and find they are correct.
What is the most likely cause for this notification failure?
An environment consists of a two-RPA, single cluster. There are 112 Consistency Groups (CGs) configured and replicating. The administrator asks you what impact an RPA failure would have.
What should you tell them?
When is the Open Replicator RecoverPoint session created for each production volume in the Consistency Group (CG)?
When determining the journal volume size, which parameters must be considered?
You are protecting a volume using the wizard in Unisphere for RecoverPoint. Which state will the new Consistency Group be in immediately after completing the wizard?
Through what does RecoverPoint support heterogeneous storage environments?
Which connectivity protocols are used to interconnect RecoverPoint clusters?
During a failover event, you have determined that the last bookmark had corrupted data. What is the fastest way to find the last good replica?
A company is currently using RecoverPoint/SE in their environment. They have purchased a VMAX which will be deployed to replace a VNX splitter at one site only.
What must be done before they can use the VMAX with RecoverPoint (RP)?
A customer is evaluating the deployment of RecoverPoint with their VMAX array. They want to deploy the RPAs in the virtual appliance form. They ask your opinion about using vRPA versus physical appliances.
What should you advise them?
A customer environment includes a two-cluster RecoverPoint/SE instance. They have a new data center 500 km away that they wish to protect with RecoverPoint.
What steps are required to connect a new cluster to their existing RecoverPoint instance?
You are adding a new vRPA to a cluster using the Add New RPAs wizard in Deployment Manager. SAN diagnostics fail and you cannot add the RPA. Pings to the vRPA and VNX iSCSI ports are returned successfully.
What is most likely the cause for this connection problem?
An application team will be performing a major update to a RecoverPoint protected application. You have been asked by the application team for the best way to ensure a quick recovery at the remote cluster in case the update fails.
In RecoverPoint, what should be done to the associated Consistency Group?
A conversion from RecoverPoint/SE to RecoverPoint/EX was just completed. What is the next required step?
What are two requirements for an EMC RPA to connect to an EMC VNX via a SAN?
A company recently acquired a new DR site and requires their production data to be replicated to this DR site.
What is an important consideration about the RecoverPoint out-of-band architecture?
A large data center is hosting storage protection solutions for multiple companies. This solution is accomplished by the hosting organization's ability to consolidate data to an environment with two VNX arrays.
How many RecoverPoint clusters can be used in this environment?
What zoning must be created in the fabric when implementing a VMAX splitter?
You are protecting a volume using the wizard in Unisphere for RecoverPoint. Which state will the new Consistency Group be in immediately after completing the wizard?
System events can be copied to the clipboard from which Unisphere for RecoverPoint view?
When selecting the semi-automatic zoning method while installing RecoverPoint/SE, which zones are displayed per RPA?
What is the maximum number of VMAX splitters that can be added to a RecoverPoint cluster?
When creating a Consistency Group (CG), what is true of RecoverPoint/SE only?
You are a storage administrator tasked with creating a Consistency Group in a RecoverPoint/EX system. You launch the Protect Volumes wizard in Unisphere and notice that the desired production volume is not available.
What would be a possible cause?
During deployment of a vRPA OVF template a temporary IP address must be set to be used by Deployment Manager in later steps.
Which IP address allocation policy should be selected?
Which RecoverPoint product(s) may be licensed by the amount of array capacity?
What is the minimum size of the journal when using Distributed Consistency Groups?
Refer to the exhibit.
A storage administrator wants to protect their distributed VPLEX volumes using RecoverPoint and the VPLEX splitter. The admin asks if there are special considerations they must be aware of.
What should you tell the admin?
Which FA ports must the production LUN be mapped to in order to perform write splitting using the VMAX splitter?
An Oracle user is currently protecting their virtual application servers with RecoverPoint. All data is stored on two VNX arrays. They will soon be adding Site Recovery Manager (SRM) to their VMware infrastructure.
What will be needed to integrate RecoverPoint functionality into their SRM deployment?
A RecoverPoint cluster contains a Consistency Group with one remote copy.
Which volume can be used to verify that snapshots are being created?
A new RecoverPoint system is being installed and the RPAs need to be upgraded to the latest version.
How should this be done?
A company has just installed a RecoverPoint solution and configured it with two clusters.
Which command will monitor system performance for both sites?
TESTED 20 Jun 2025