Get HPE3-U01 Dumps : Verified Aruba Certified Network Technician Exam (ACNT)

 Switches and routers are both networking devices that operate at different layers of the OSI model and perform different functions. The key differences between L2 switches and routers are:

• Switches operate at the data link layer (Layer 2) of the OSI model, while routers operate at the network layer (Layer 3). This means that switches forward frames based on the MAC addresses of the source and destination devices, while routers route packets based on the IP addresses of the source and destination networks.
• Switches build a MAC table that maps MAC addresses to switch ports, while routers build a routing table that maps IP addresses to next-hop interfaces. The MAC table is used by switches to determine which port to send a frame to, while the routing table is used by routers to determine which interface to send a packet to.
• Switches offer a considerably higher port density than routers, meaning that they can connect more devices to the network. Switches typically have dozens or hundreds of Ethernet ports, while routers usually have a few Ethernet ports and other types of ports such as ADSL, cable, fiber, dial-up, etc. Switches are used to create LAN segments, while routers are used to connect different networks or subnets.
• Switches are faster than routers because they do not take up time looking at the network layer header information. Switches can forward frames at wire speed, while routers need to process packets at the network layer and perform additional functions such as NAT, firewall, QoS, etc.

References: Switch (L2/L3) Vs Router: Comparison and Differences in TCP/IP Networks, Key Differences Between Routers and Different Types of Switches, Layer 2 Switch - How it operates, when to use it - Network Encyclopedia, Layer 2 switching - Study-CCNA, Differences Between Layer 2 and Layer 3 Switches?Which one do you need?

To establish a secure web connection to YouTube.com, the computer will run two protocols: DNS and HTTPS. DNS (Domain Name System) is a protocol that translates domain names into IP addresses, which are used to identify and locate web servers on the internet. HTTPS (Hypertext Transfer Protocol Secure) is a protocol that encrypts and authenticates data transfer between a web browser and a web server, ensuring the security and integrity of the communication.

The computer does not need to run DHCP (Dynamic Host Configuration Protocol), FTP (File Transfer Protocol), or HTTP5 (a non-existent protocol) to connect to YouTube.com. DHCP is a protocol that assigns IP addresses to devices on a network automatically, but the computer already has a static address configured. FTP is a protocol that transfers files between a client and a server, but it is not used for web browsing. HTTP5 is not a valid protocol name, and it is likely a typo for HTTP (Hypertext Transfer Protocol), which is the unsecure version of HTTPS. References:

• Aruba Certified Network Technician (ACNT) | HPE Aruba Networking
• 6 Network Security Protocols You Should Know | Cato Networks
• What is HTTPS? | Cloudflare

A hardwire desktop PC belongs to the category of stationary devices, which are devices that are fixed in one location and do not move. Stationary devices typically have a constant power supply and a wired network connection. Examples of stationary devices are desktop PCs, servers, printers, and IP phones. Stationary devices are different from mobile devices, which are devices that can move from one location to another and connect to the network wirelessly. Mobile devices can be further classified into somewhat mobile devices, highly mobile devices, and intermittent mobile devices, depending on their mobility patterns and network requirements. Examples of mobile devices are laptops, tablets, smartphones, and wearable devices. References:

• Aruba Certified Network Technician (ACNT) | HPE Aruba Networking
• Aruba Documentation Portal

According to the Ethernet cable standards, Cat 6 UTP-based cabling can support 1 Gbps data rates up to 100 meters (328 feet) of cable length. This is the maximum recommended distance for a single cable run between a host and the switch where it is plugged in. If the cable length exceeds 100 meters, the signal quality may degrade and cause errors or lower performance. Cat 6 UTP-based cabling can also support 10 Gbps data rates up to 37-55 meters (121-180 feet), depending on the alien crosstalk atmosphere. However, for 10 Gbps data rates, Cat 6a UTP-based cabling is preferred, as it can support the full 100 meters of cable length. References https://networkengineering.stackexchange.com/questions/81114/degradation-of-signal-quality-as-a-function-of-cat-6-cable-length

https://www.howtogeek.com/813419/how-long-can-an-ethernet-cable-be/

According to the Aruba Network Technician (ACNT) documents and learning resources, the valid configurable “Client VLAN Assignment” options for a Bridge-based WLAN in Aruba Central are native VLAN, automatic VLAN, and static VLAN. These options allow you to specify how the VLAN ID for the WLAN clients is determined.

• Native VLAN: This option allows you to use the native VLAN of the AP’s Ethernet port as the VLAN ID for the WLAN clients. The native VLAN is the default VLAN that carries untagged traffic on a trunk port. This option is useful when you want to simplify the VLAN configuration and use the same VLAN for all the WLAN clients connected to the same AP.
• Automatic VLAN: This option allows you to use the VLAN ID assigned by a DHCP server to the WLAN clients. The DHCP server can use attributes such as MAC address, hostname, or vendor class to assign different VLAN IDs to different WLAN clients. This option is useful when you want to dynamically assign VLANs based on the client characteristics or policies.
• Static VLAN: This option allows you to specify a single VLAN ID for all the WLAN clients. You can either enter a VLAN ID manually or select a named VLAN from the drop-down list. A named VLAN is a VLAN that has a user-defined name associated with it for easy identification. This option is useful when you want to assign a fixed VLAN to a WLAN SSID.

References: