A hub is a simple Layer 1 (Physical Layer) device that does not understand MAC addresses or IP addresses. It simply repeats electrical signals to all connected ports without inspection or filtering.

MTCNA Course Material – OSI Layer Device Roles:

“Hubs operate at the Physical Layer. They do not process frames or packets and function purely as repeaters.”

René Meneses MTCNA Study Guide – OSI Devices:

“Hubs are Layer 1 devices. They send bits — not frames — and have no concept of MAC addresses.”

Other options:

A: Session layer is Layer 5, handles sessions between applications

C: Switches/bridges operate at the Data Link layer (Layer 2)

D: Application layer (Layer 7) is for user-level software like HTTP, FTP, etc.

Final Answer: BQUESTION NO: 138 [Cisco IOS – Access List Verification]

Which command is used to determine if an IP access list is enabled on a particular interface?

A. show access-lists

B. show interface

C. show ip interface

D. show interface access-lists

Answer: C

The command show ip interface displays the status of IP-level interface parameters, including whether an access list (ACL) is applied inbound or outbound.

Cisco IOS Command Reference – Interface ACL Check:

“Use show ip interface to verify whether an access list is applied to the interface and in which direction (in or out).”

René Meneses MTCNA Study Guide – Cisco Access List Monitoring:

“To verify ACL assignment to an interface, use show ip interface. It provides ACL status along with IP addressing info.”

Breakdown:

A: show access-lists ? shows ACL contents, not interface bindings

B: show interface ? shows interface stats, not ACL usage

D: Invalid syntax in Cisco IOS

Final Answer: CQUESTION NO: 139 [RouterOS Introduction – Transport Protocols]

Which protocol does DHCP use at the Transport layer?

A. IP

B. TCP

C. UDP

D. ARP

Answer: C

DHCP (Dynamic Host Configuration Protocol) operates over UDP:

Client uses UDP port 68

Server uses UDP port 67

It is a connectionless protocol, and because clients typically do not yet have IP addresses, UDP is used due to its simplicity.

MTCNA Course Material – DHCP Protocol Layering:

“DHCP uses UDP for communication between clients and servers. TCP is not used due to the stateless, broadcast nature of DHCP discovery.”

René Meneses MTCNA Study Guide – Port Assignments:

“UDP 67/68 are used by DHCP. TCP is not used because clients lack IPs initially.”

Other options:

A: IP is the network layer, not transport

B: TCP is used by reliable services (FTP, HTTP)

D: ARP resolves IP-to-MAC; unrelated to DHCP transport

Final Answer: CQUESTION NO: 140 [Cisco IOS – Remote Access Configuration]

Which of the following commands will allow you to set your Telnet password on a Cisco router?

A. line telnet 0 4

B. line aux 0 4

C. line vty 0 4

D. line con 0

Answer: C

The correct line configuration for remote Telnet (or SSH) access in Cisco IOS is via the virtual terminal (vty) lines. Typically, Cisco routers reserve 5 lines: vty 0 4. You then apply the password and login commands under this context.

Cisco IOS Configuration Guide – Telnet/VTY Setup:

“Use line vty 0 4 to configure access for Telnet sessions. Then use password and login to enforce authentication.”

René Meneses MTCNA Study Guide – Cisco Access Configuration:

“VTY lines (virtual terminal) handle Telnet and SSH sessions. Console and aux lines are for local access.”

Other options:

A: line telnet is not a valid command

B: line aux ? used for modem or auxiliary port access

D: line con 0 ? used for console (local) access, not remote

????????????????????????????????????????????????????????????

To upgrade or install a new Cisco IOS image on a router, you typically copy the IOS image file from a TFTP server into the router’s flash memory. The correct syntax is:

copy tftp flash

This command tells the router to copy the IOS image from a TFTP server into flash storage, where it can be booted.

Cisco IOS Documentation – Image Upgrade Process:

“Use the command copy tftp flash to transfer an IOS image from a TFTP server to the router’s flash memory.”

Other options:

A: copy tftp run – invalid; you cannot copy into the running-config that way

B: copy tftp start – used to copy configuration, not IOS image

C: config net – an older and deprecated command, not for IOS upgrades

Final Answer: DQUESTION NO: 122 [RouterOS Introduction – ICMP and Diagnostics]

Which protocol does Ping use?

A. TCP

B. ARP

C. ICMP

D. BootP

Answer: C

Ping is a diagnostic utility used to test reachability between devices. It sends ICMP Echo Request packets and waits for ICMP Echo Replies. ICMP (Internet Control Message Protocol) is used for these types of control messages and is encapsulated within IP.

MTCNA Course Material – Diagnostic Tools:

“Ping uses ICMP Echo Requests to verify if a destination is reachable. It does not use TCP or UDP.”

René Meneses MTCNA Study Guide – Ping and ICMP:

“Ping uses ICMP, not TCP or ARP. ICMP packets are used to check basic connectivity.”

MikroTik Wiki – Ping Tool Description:

“Ping works by sending ICMP packets. It cannot use TCP.”

Other options:

TCP: Used by protocols like HTTP, FTP

ARP: Resolves IP to MAC, not used for ping

BootP: DHCP-related protocol, not diagnostic

Final Answer: CQUESTION NO: 123 [Cisco – Frame Relay Troubleshooting]

What command will display the line, protocol, DLCI, and LMI information of an interface?

A. sh pvc

B. show interface

C. show frame-relay pvc

D. show run

Answer: C

In Cisco IOS, to display detailed Frame Relay virtual circuit information, including the line status, protocol status, DLCI (Data Link Connection Identifier), and LMI (Local Management Interface) details, the correct command is:

show frame-relay pvc

Cisco IOS Command Reference – Frame Relay:

“The show frame-relay pvc command displays information about PVC status, including DLCI numbers and LMI statistics.”

Breakdown:

A: sh pvc – shorthand and ambiguous, may not be recognized

B: show interface – general interface stats but lacks detailed LMI/DLCI info

C: show frame-relay pvc –?correct, provides detailed DLCI/LMI info

D: show run – shows current configuration, not real-time PVC status

Final Answer: CQUESTION NO: 124 [Networking Fundamentals – Ethernet and Switching]

How many collision domains are created when you segment a network with a 12-port switch?

A. 1

B. 2

C. 5

D. 12

Answer: D

Each port on a switch creates its own collision domain. Unlike hubs (which extend a single collision domain), switches segment each interface, allowing full-duplex communication and eliminating collisions.

MTCNA Course Material – Ethernet Switching Concepts:

“Each switch port is a separate collision domain. A 24-port switch creates 24 separate collision domains.”

René Meneses MTCNA Study Guide – Collision and Broadcast Domains:

“Switches break up collision domains per port, unlike hubs.”

Therefore, a 12-port switch creates 12 individual collision domains.

In a MikroTik Hotspot environment, you can bypass authentication for specific users using the IP Bindings feature. This feature lets you mark a host as bypassed (authorized without login), blocked, or regular.

A. Users ? Incorrect. This contains login credentials for regular authenticated users.

B. IP bindings ? Correct. This allows specific devices (by IP or MAC) to bypass login requirements.

C. Walled-garden ? Incorrect. This allows unauthenticated access to specific domains or URLs, not devices.

D. Walled-garden IP ? Incorrect. Similar to option C, it controls destination IP access, not client exemption.

Extract from Official MTCNA Course Material – Hotspot:

“To allow a specific host to bypass authentication, use IP Bindings with the ‘bypassed’ type.”

Extract from René Meneses MTCNA Study Guide – Hotspot Section:

“The IP Bindings tab in the Hotspot menu is used to set specific IPs or MACs as bypassed. This exempts them from login.”

Extract from Terry Combs MTCNA Notes – Hotspot Bypass:

“Use IP Bindings for fixed clients (e.g., printers or servers) that should not be challenged by the Hotspot portal.”

===========