Crack4sure Logo
3 Months Free Update
3 Months Free Update
3 Months Free Update
You have quiesced a volume to stabilize the contents of a destination just prior to a snapshot. What is the next logical command that you would issue after the snapshot is complete?
An aggregate is composed of twelve 36-Gigabyte disks. A drive fails and only 72-Gigabyte spare disks are available Data ONTAP will then perform what action?
When cabling a standard storage appliance for SyncMirror. disk pool 1 volumes must be cabled to Fibre Channel adapter(s) located in what range of slots on the FAS960 appliance?
Which one of the following commands is used to specify the destination appliance(s) that are allowed to replicate (pul data from the source appliance?
Which OSSV package would you use to perform an OSSV unattended installation?
How can you "throttle" Snap Vault updates and baseline transfers so that the primary or secondary is not transmitting data as fast as it can?
Which two tools should an administrator use to manage NVMe namespaces? (Choose two.)
In a synchronous SnapMirror configuration, the soui'ce storage appliance exhibits high latency due to user traffic and rapid data change from SnapMirror transactions.Which one of the following tuning methods best resolves this performance behavior? Edit the /etc/snapmirror.conf file on the destination storage appliance and set:
The SnapVault secondary system allows you to keep a separate schedule of Snapshot copies from your primary system.
Which NetApp solution enables block-level backup and restore from ONTAP to StorageGRID?
Which option of the snap restore command allows you to specify a different directory, as long as the directory already exists?
In a fabric-attached MetroCluster, a "site failure" is described as a __________.
Due to the sensitive nature of AutoSupport messages, what transport protocol should a storage administrator configure?
You cannot disable the SyncMirror license if one or more mirrored volumes exist.
Which objects can be restored by a single SnapRestore command? (Choose three)
To restore a primary SnapVault qtree to the exact qtree location on the primary storage system (from which it was backed up), you must:
The NearStore system is not the recommended secondary storage appliance for Open System SnapVault.
Node 1 in a clustered pair detects that it has lost connectivity to one of its disk shelves. Node 1 is still up, but it cannot see one of its disk shelves. However, the partner node, Node 2, can see all of Node 1s disk shelves. Which one of the following features will cause Node 2 to monitor this error condition for a period of three minutes (by default), and then forcibly take over Node 1 if the error condition persists?
Which one of the following statements does not apply to the SnapMirror visibility-interval variable?
Normally, before you split a SyncMirror volume, you ensure that both plexes are
If an error message indicates that the cluster interconnect adapter itself is faulty, what is your corrective action?
Open System SnapVault agents can be installed on all non-Network Appliance platforms.
The required hardware to add SyncMirror to an existing Clustered Failover system consists of:
For each Open Systems platform directory to be backed up to the SnapVault secondary storage system, you must execute _____ from the primary to secondary storage system.
Which one of the following statements apply to the Free Space Estimator utility?
Which ONTAP feature combines multiple writes into a single 4K block on the aggregate?
SnapVaulr snapshots for SnapLock volumes are deleted automatically according to the retention count set in the SnapVault schedule?
Fill in the blank for the following statement: To manage a SnapVault backup through a commercial NDMP application, you must specify a_____authorized through that application.
Which ONTAP authentication method must be added to enable two-factor authentication to an existing administrator's SSH login?
Which one of the following actions will cause a currently in sync snapmirror relationship to fall out of sync?
You are troubleshooting a clustered failover problem at a customer site. The customer explains that both storage appliances were NFS mounted onto the Solaris host. You attempt to create a file on the NFS mount point for the inaccessible appliance, but you get the following error:NFS server filer2 not responding still trying.Symptoms:
1) When not in takeover mode, both storage appliances operate normally.
2) In takeover mode, the taken over node is not accessible on the network.You perform a "cf giveback" and you can now create a file over NFS on both appliances.
What should vou do first to resolve this issue?
Refer to the exhibit.
A company has three servers that are using the iSCSI protocol to connect to a two node NetApp ONTAP cluster. The server administrator notices that half of the paths are down. The administrator checks the ONTAP cluster and notices the servers are logging into only the first controller.
Which two steps should the administrator take to troubleshoot the issue? (Choose two.)
Fill in the blanks for the following statement:
The qtree specified for_____must not exist on the secondary system before you run the_____command.
A NearStore system or storage appliance can operate as a secondary and primary system at the same time.
What is the minimum number of HA pairs required for Epsilon to be automatically assigned?
Which one of the following statements does not apply to Nearstore Personality?
When using a Protection Manager policy to manage Open Systems SnapVault backups on a UNIX server, which three are valid objects to include in the data set? (Choose three.)
The required hardware to add SyncMirror to an existing system would be ___________.
Data ONTAP uses inodes in an active file system to reference__________________.
A mirrored volume. volX. is composed of twelve 36-Gigabyre disks: six in volX/plex0. six in volX/plex1. A drive fails in plexl. bur pool 1 contains only 72-Gigabyte spare disks. Data ONTAP will do which of the following?
Which three of the following configurations would increase data transfer rates for traditional volume SnapMirror?
One week ago you performed a single file SnapRestore from a snapshot other than the most recent. You now notice that the storage appliance is now taking longer to perform snapshot deletions. Which one of the following reasons is the most likely cause of this problem?
It is the use of the -Lflag in the snapmirror initialize command and the subsequent successful level 0 transfer that causes the destination volume to become snaplocke?
Exhibit.
An administrator has a NetApp AFF cluster with Cloud Tiering enabled on all data using the snapshot-only policy. When restoring files, users report slow response times.
What is the highest latency seen during restore?
Refer to the exhibit.
An administrator creates a new qtree and an associated export policy. When the client tries to connect, they are denied.
What should the administrator do?
What are two ways that an administrator can define a new consistency group? (Choose two.)
Which SyncMirror command mirrors an existing unmirrored aggregate where Data ONTAP selects the disk drives?
Which option of the snap restore command allows you to specify a different directory, as long as the directory already exists?
When Data ONTAP creates a weekly, nightly, or hourly snapshot, the value of n (as shown by the UNIX Is command) is adjusted for all the weekly, nightly, or hourly snapshots. The higher the value of n. the_________the snapshot.
In a synchronous SnapMirror configuration, the source storage appliance exhibits high latency due to user traffic and rapid data change from SnapMirror transactions. Which one of the following tuning methods best resolves this performance behavior? Edit the /etc/snapmirror.conf file on the destination storage appliance and set:
A mirrored volume has a failed disk, but there are no available spares in the pool from which the degraded plex was built. Data ONTAP will:
TESTED 09 May 2024