Get CWAP-404 Dumps : Verified Certified Wireless Analysis Professional

The data rate at which the PHY preamble was transmitted is 6 Mbps. The PHY preamble is a part of the PPDU that is transmitted before the PHY header and the PSDU. The PHY preamble consists of a series of training fields that help the receiver to detect and synchronize with the signal. The PHY preamble is always transmitted at a fixed data rate that depends on the type of PPDU (e.g., OFDM, HT, VHT, HE). For an 802.1 lac data frame on channel 52, which uses VHT PPDUs, the data rate for the PHY preamble is 6 Mbps. This data rate does not depend on MCS (Modulation and Coding Scheme), which only affects the data rate for the PSDU. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 99-100

 In the 2.4 GHz band, probe requests are usually sent at the minimum basic rate from an unassociated STA. A probe request is a type of management frame that is transmitted by a STA to discover available BSSs in its vicinity. A probe request can be sent on one or more channels in either passive or active scanning mode. In passive scanning mode, a STA listens for beacon frames from APs on each channel. In active scanning mode, a STA sends probe requests on each channel and waits for probe responses from APs. A probe request is usually sent at the minimum basic rate, which is the lowest data rate among the supported rates that is required for all STAs to join and communicate with a BSS. The minimum basic rate can vary depending on the configuration of each BSS, but it is typically one of these values: 1 Mbps, 2 Mbps, 5.5 Mbps, or 11 Mbps in the 2.4 GHz band. The other options are not correct, as they do not reflect how probe requests are usually sent in the 2.4 GHz band. MCS 0 is a modulation and coding scheme used by 802.11n/ac devices in either band, but it is not a data rate per se. 6 Mbps is a data rate used by OFDM devices in either band, but it is not usually configured as a minimum basic rate in the 2.4 GHz band. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 123-124

Every Beacon frame must contain a DTIM is not a true statement concerning DTIMs. DTIM stands for Delivery Traffic Indication Message, and it is a subfield within the TIM (Traffic Indication Map) element in a Beacon frame. The DTIM indicates how many Beacon frames (including the current one) will appear before the next DTIM. For example, if the DTIM interval is set to 3, it means that every third Beacon frame will contain a DTIM. Buffered broadcast and multicast traffic will be transmitted following a DTIM, so that STAs in power save mode can wake up and receive them. The DTIM interval can also dictate when an STA will wake up to listen to Beacon frames, as some STAs may choose to only listen to Beacon frames that contain a DTIM . References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 200; CWAP-404 CertifiedWireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 201.

The function of 802.11 management frames is to manage the BSS. A BSS (Basic Service Set) is a group of STAs (stations) that share a common SSID (Service Set Identifier) and communicate with each other through an AP (access point) or directly in an ad hoc mode. Management frames are one of the three types of 802.11 frames, along with control and data frames. Management frames are used to establish, maintain, and terminate associations between STAs and APs, as well as to advertise and discover BSSs, exchange security information, report errors, and perform other management functions. The other options are not correct, as they are not functions of 802.11 management frames. Prioritizing network administration traffic, communicating configuration changes between WLAN controller and APs, and managing the flow of data are functions of other types of frames or protocols. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 120-121

The length of an AIFS (Arbitration Interframe Space) is calculated by multiplying the AIFSN (Arbitration Interframe Space Number) by the Slot Time and adding the SIFS (Short Interframe Space). An AIFS is a variable interframe space introduced by 802.11e to help prioritize medium access for different Access Categories (ACs). An AC is a logical queue that corresponds to a QoS (Quality of Service) level for different types of traffic. Each AC has a different AIFSN value, which determines how long it has to wait before attempting to access the medium. A lower AIFSN value means a higher priority and a shorter waiting time. The Slot Time is a fixed value that depends on the PHY type and channel width. The SIFS is the shortest interframe space that is used for high-priority transmissions, such as ACKs or CTSs. The formula for calculating the AIFS length is: AIFS = AIFSN * Slot Time + SIFS. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 7: QoS Analysis, page 194-195